Search found 220 matches
- Wed Aug 31, 2011 3:44 pm
- Forum: General
- Topic: Black box T2 Whats really needed?
- Replies: 9
- Views: 13350
Black box T2 Whats really needed?
Took it out today to check behind it for any rust which luckily and to my surprise there was none. I decided to simplify it as well while I was there and the only thing I have connected up is the MAP sensors and idle enrichment knob. Started up fine and took it around the block and couldn't notice a...
- Fri Aug 26, 2011 5:40 pm
- Forum: General
- Topic: Cold air intake mod (T2).
- Replies: 0
- Views: 11027
Cold air intake mod (T2).
This mod requires that you have the heater removed. Basically you want to run the intake into the cabin, How this is done is with 2X 90degree silicon/rubber bends. 1X 47mm mandrel bent U bend (or size to match your silicon/rubber bends). 1X 47mm, 40mm long bit of pipe (or size to match your setup)....
- Fri Aug 26, 2011 2:03 pm
- Forum: General
- Topic: Warmed up water temp?
- Replies: 3
- Views: 6411
- Thu Aug 25, 2011 2:06 pm
- Forum: General
- Topic: Warmed up water temp?
- Replies: 3
- Views: 6411
Warmed up water temp?
What should the warmed up water temp be? Got a water temp gauge installed and temps seem to be a bit strange. City driving with very little turbo assist temp stays around 80C Motorway driver with some turbo assist temp gets up to 90C Sitting at lights gets up to stays between 95C-100C where the fan ...
- Sat Aug 20, 2011 12:29 pm
- Forum: General
- Topic: wheel bearing,part numbers?
- Replies: 6
- Views: 14283
- Tue Aug 16, 2011 7:50 pm
- Forum: General
- Topic: wheel bearing,part numbers?
- Replies: 6
- Views: 14283
Dont have a part number but did my rear ones 6 months ago. No where had any that would suite but my mate at appco managed to source some bearings from a completely different thing and they did the trick and still going strong. Ill have to ask him what they were for but it was something crazy like a ...
- Fri Jul 29, 2011 11:13 am
- Forum: General
- Topic: Any of you guys taking your city to NZH NIMM
- Replies: 0
- Views: 10860
Any of you guys taking your city to NZH NIMM
Just wonder if Ill see any of you guys there?
Details here
http://nzhondas.com/upper-north-island/ ... 011-a.html
Details here
http://nzhondas.com/upper-north-island/ ... 011-a.html
- Wed Jul 20, 2011 8:27 am
- Forum: General
- Topic: FCD Question (James, BOOSTBOY; if you're still there?)
- Replies: 7
- Views: 9356
It runs off the chip, but doesnt like my rom emulator. Need to run a socket booster. Cold start problem was because the rom emulator wasn't getting enough power from the socket when cranking a cold engine. Im running a T1 core with T2 parts on my T2 engine with out problem so id say the problem is e...
- Mon Jul 18, 2011 10:35 am
- Forum: General
- Topic: FCD Question (James, BOOSTBOY; if you're still there?)
- Replies: 7
- Views: 9356
- Sun Jul 10, 2011 4:39 pm
- Forum: General
- Topic: FCD Question (James, BOOSTBOY; if you're still there?)
- Replies: 7
- Views: 9356
- Sat Jul 09, 2011 10:10 am
- Forum: General
- Topic: EGR valve in T2
- Replies: 7
- Views: 10709
- Sat Jul 09, 2011 10:10 am
- Forum: General
- Topic: FCD Question (James, BOOSTBOY; if you're still there?)
- Replies: 7
- Views: 9356
I wouldn't recommend using a potentiometer since then all your map readings will be off making the engine run leaner. Instead use a voltage cap. Just make sure you have good boost control since there wont be a limit any more, or alternately you can add a voltage switch as well and set it to trigger ...
- Tue Jun 21, 2011 10:30 am
- Forum: General
- Topic: [How To] Launch Controll On City Turbo
- Replies: 2
- Views: 4602